The publisher is making several good observations regarding How to Install a Bathtub Yourself overall in the content further down.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably hard job. If the old tub is conveniently obtainable, the task can move rapidly; if you have to open a wall surface to remove the old bathtub as well as position the brand-new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the brand-new one. Make certain you have qualified on your own for the work and are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to consider employing one before you begin. Chances are you might need an expert plumber to make tube links.
This article will assist you set up a brand-new bath tub in your washroom if you have actually currently bought a new tub and don't need to alter the plan of your previous water pipelines.
Your devices and also product list need to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub till the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water supply as well as examine all joints as well as new pipework for leakages and tighten them if needed. Load the bathtub as well as also inspect the overflow electrical outlet and the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub must wait until the tub has been made use of at least when as this will resolve it into its final setting.
Getting ready for the Installment
First of all, the sustaining frame supplied with the bath needs to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, creating the water to penetrate the wall between the bath as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can fracture rather early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
As a passionate person who reads on How to Install a Bathtub Yourself, I figured sharing that segment was really helpful. Are you aware of anybody else who is sincerely interested in the topic? Feel free to share it. Thanks a lot for going through it.
Book A Service